
Electrical faults
Circuit breaker keeps tripping: overload, short circuit or faulty breaker
An overload, a short circuit and a worn breaker all look the same from the meter box. How and when it trips tells them apart.
A circuit breaker trips when too much current flows through the circuit it protects. If it trips after things have been running for a while, the usual cause is an overload: too many appliances on one circuit. If it trips instantly, often with a bang or a flash, it is more likely a short circuit. If it trips with almost nothing running, the breaker itself may be failing.
The rule is to reset it once. If it trips again straight away, leave it off and get it looked at. Never fit a bigger breaker to stop the tripping, because the breaker is the thing stopping the cable from overheating.
Is it dangerous?
The breaker tripping is the protection doing its job. The cause can be dangerous. Stop and get help if:
- You heard a bang, saw a flash, or there is a burning smell, smoke or scorch marks. Switch off at the main switch if safe, and call 000 if there is fire.
- The breaker, the switchboard or a power point feels warm.
- It trips again the moment you reset it.
- Anyone felt a tingle or shock.
What you can safely check
- Work out what was running. Heaters, kettles, air fryers, irons, hair dryers and portable air conditioners draw a lot. Two of them on the same circuit is the classic overload.
- Turn off and unplug the big loads on that circuit before you reset.
- Reset once. If it holds, turn things back on one at a time and see where it trips. If it trips with one appliance on its own, that appliance is suspect.
- Spread the load. If it only trips with several things on at once, move one of them to a power point on a different circuit.
- If it trips instantly on reset with everything off, leave it off and call an electrician.
What usually causes it
Overload
The most common cause by far. A circuit is rated for a certain current and the breaker trips when the total load passes that point for long enough. It tends to happen in winter with heaters, and in kitchens where several high draw appliances run together. It is not a fault in the wiring, but it is telling you the house needs more circuits than it has.
Short circuit
Active and neutral, or active and earth, touching directly. The current spikes and the breaker trips immediately. Causes include a damaged appliance cord, a failing appliance, a nail or screw through a cable, pest damage, or a loose conductor inside a fitting. It needs finding before that circuit is used again.
A worn or faulty breaker
Breakers age. An old one can trip well below its rating, or develop a poor connection that runs hot. If a breaker trips on very little load or feels warm to the touch, it needs testing and probably replacing.
Air conditioner and oven circuits
Air conditioners and ovens usually have their own dedicated circuits. An air conditioner that trips its breaker on a hot afternoon may have a compressor or fan motor starting to fail, a loose connection, or a circuit that was undersized when it went in. An oven or cooktop that trips may have a failing element or a burnt terminal. Both are fixed appliances, so the checking is ours rather than yours.
RCBOs
Newer boards often use RCBOs, which combine a circuit breaker and a safety switch in one device. An RCBO trips for overload, short circuit or leakage to earth. If yours has one, read safety switch keeps tripping as well.
What an electrician does
- Asks how fast it trips and what was running, because that separates overload from short circuit.
- Checks the breaker rating against the cable it protects, and tests the breaker itself.
- Measures the load on the circuit to see whether it is genuinely overloaded.
- Tests the circuit insulation and traces any short to the fitting, cable or appliance.
- Checks terminations in the board and at outlets for heat damage.
- Gives you a fixed price for the fix, which might be a repair, a new dedicated circuit, or a board with room for one.
A board that keeps running out of capacity is one of the signs covered in how to tell if your switchboard is overloaded or unsafe. If you are adding an air conditioner, ask about the circuit when you get the quote for a split system or ducted system.
When to call
Call us if it trips instantly on reset, trips with a single appliance that works fine elsewhere, trips with very little running, or keeps tripping on an air conditioner or oven circuit. Our fault finding service is charged hourly with the rate told up front, then a fixed price for the repair. If it is simply overloaded and you want more circuits, a switchboard upgrade is the usual answer. Get in touch between 8:30am and 5pm, seven days. Outside those hours leave the circuit off, and for burning or smoke switch off at the main switch if safe and call 000 if there is fire.
FAQs
Questions on this
Why does my circuit breaker trip when I turn on the heater?
Most likely the heater and whatever else is on that circuit together draw more than the circuit is rated for. Move the heater to a different circuit. If it trips with the heater alone, the heater may be faulty.
Can I fit a bigger breaker so it stops tripping?
No. The breaker is sized to protect the cable behind it. A bigger breaker lets the cable overheat, which is how a nuisance becomes a fire risk. The fix is a new circuit or less load, not bigger protection.
Do circuit breakers wear out?
Yes. Older breakers can weaken and trip below their rating, or run warm. If a breaker trips with very little load on it, or feels warm, it needs testing.
Why does the power keep tripping when the air conditioner starts?
Air conditioners draw a surge when the compressor starts. A healthy unit on a correctly sized dedicated circuit should not trip it. Repeated trips point at the unit, the circuit or a loose connection.
Get a quote
Breaker tripping and you want it found?
Tell us which circuit, what was running and how quickly it trips. That narrows it down before we arrive.