A lit brass pendant light with glass globes on a living room ceiling in Yangebup

Electrical faults

Lights flickering: one bulb, one circuit or the whole house

Where the flicker happens tells you most of what you need to know. One light is usually the light. A loose connection is the one to worry about.

If one light flickers, the cause is usually that light: a failing lamp, an LED driver on its way out, or an LED that does not suit the dimmer it is on. If every light in the house flickers, the cause is more likely the supply, especially if the neighbours notice it too. If the lights on one circuit flicker, or the flicker comes with buzzing, warmth or a smell, suspect a loose connection, which is the dangerous one.

Start by working out which of those three you have. It takes a few minutes, needs no tools, and tells you whether to change a lamp, ring Western Power, or call an electrician.

Is it dangerous?

A single flickering LED is a nuisance. Flicker is a warning when it comes with any of these:

  • A burning or hot plastic smell, smoke, or scorch marks on a switch, light fitting or the switchboard. Switch off at the main switch if safe, and call 000 if there is fire.
  • Buzzing, crackling or a warm switch plate.
  • Lights that go noticeably brighter as well as dimmer, or appliances behaving strangely at the same time. That can be a neutral fault, which is serious. Switch off at the main switch if safe and call Western Power on 13 13 51.
  • A tingle from a tap, the shower or any metal fitting. Do not touch it again, switch off at the main if safe, and call Western Power on 13 13 51.

What you can safely check

  1. One light or many? Walk the house and note which lights flicker.
  2. Swap the lamp. For a lamp you can change, switch it off, let it cool, and try a new one. If the flicker goes, that was it. Integrated LED fittings, where the light is built into the fitting, cannot be swapped, and the driver inside may be the problem.
  3. Check the dimmer. If the flickering lights are on a dimmer, check the lamps are marked dimmable. A non-dimmable LED on a dimmer will flicker.
  4. Note what triggers it. Does it happen when the air conditioner, oven, pool pump or washing machine starts? Every time, or randomly?
  5. Ask the neighbours. If they see it too, it is the network. Check the Western Power outage map, and report it on 13 13 51.

Do not take light fittings or switch plates apart. The connections behind them are fixed wiring.

What usually causes it

The lamp or its driver

LEDs run from a small driver, either inside the lamp or in the fitting. Drivers fail with age and heat, and a failing one often flickers before it dies. Cheap LEDs fail sooner.

Dimmer compatibility

Many older dimmers were designed for incandescent and halogen lamps. LEDs draw so little that the dimmer cannot control them smoothly, which shows up as flicker, shimmer or a faint glow when switched off. The fix is a dimmer and lamps that suit each other.

Big loads starting

Air conditioners, pool pumps and other motors draw a surge on start. A brief dip can be normal. A large or long dip suggests the circuit is carrying too much, or there is resistance somewhere in the chain.

A loose connection

The one that matters. A loose terminal at a switch, a fitting, a joint in the roof or in the switchboard makes intermittent contact. Each time it does, it heats. It tends to get worse, not better.

The supply

Flicker across the whole house, or across the street, often comes from the network. A neutral fault in the service to the house is the serious version: some lights go bright, others dim, and appliances misbehave.

What an electrician does

  1. Establishes the pattern: which lights, how often, and what else is running.
  2. Checks the lamps, drivers and dimmers on the affected lights.
  3. Measures the supply voltage at the board, and under load, to see whether the problem is coming in from outside.
  4. Checks terminations at the switches, fittings and board on the affected circuit, looking for heat damage.
  5. Repairs the connection, replaces the driver or dimmer, or tells you the problem is on the network side and who to call.

When to call

Call Western Power on 13 13 51 if it is affecting the street, if lights are going brighter as well as dimmer, or if there is a tingle from a tap. Call us if one circuit flickers, if a new lamp does not fix it, if there is buzzing or warmth, or if the flicker is getting worse. Our fault finding service traces it, and if the answer is new fittings or compatible dimmers, our lighting installation team does that too. Get in touch between 8:30am and 5pm, seven days.

Flicker on one circuit can be an early sign of the faults described in burning smell from a power point. If part of the house goes dark rather than flickering, see half the house has no power.

FAQs

Questions on this

Why do my LED lights flicker when dimmed?

Usually because the LED lamp or its driver is not compatible with the dimmer. Not every LED is dimmable, and not every dimmer suits LEDs. Matching the dimmer and the lamps normally fixes it.

Why do my lights dim when the air conditioner starts?

A large motor draws a surge as it starts, and a brief dip can be normal. If the dip is large, lasts, or is getting worse, the circuit or a connection needs checking.

Is flickering lights a sign of a fire risk?

It can be. Flicker caused by a loose connection means that connection is heating. Flicker with buzzing, a burning smell or a warm switch is a reason to switch off and call an electrician.

Who do I call if the whole street is flickering?

Western Power, on 13 13 51. Flicker or dimming across several houses is a network issue, not something inside your home.

Get a quote

Flicker you cannot explain?

Tell us which lights, how often, and what else is running when it happens. That usually tells us where to start.